11.18.2011

The Doom Scythe


Well, fine.  If everyone else is going to scratch-build Night Scythes and Doom Scythes, I might as well, too...

First off, this isn’t going to be spectacular, so if you’re looking for something on par with the Plaguereaper or the Rhino fleet, I’m afraid this won’t be it.  It’s a safe bet that Games Workshop is going to put out an actual Doom/ Night Scythe model when the next big Necron release happens, and a few weeks after that there are going to be a ton of great templates by people much more skilled (and with more free time) than me.  I’m looking to make something that will be a quick, decent stand-in for now.

And, as usual, I want to do it cheap.

I’m not doing templates for this, so I may be over-describing things a bit to make it easier to follow along.  Also, for most of this post, I’m just going to call it a Scythe.  We can get particular next time when I do details.

Let’s start with the basics.  I decided the outside edge of the Scythe was probably close to an 8 1/2” circle.   How did I decide this size?  Well, someone over at the Bell of (LINK) Lost Souls cleverly pointed out that the Scythe sprues would have to fit in the existing boxes.  The inside of your standard Chimera/ Rhino/ Monolith box measures 11 1/4” x 8 7/8”.  I’m also going off the assumption that the hull is going to be mostly one piece (maybe a top and a bottom section).

I drew two diagonals to find the center of a frozen pizza box.  Then, using a compass, I drew out an 8 1/2” circle.  I also drew a line that went straight through the center point.  This is going to be a front-back reference line for the model.

Helpful Hint – The model is going to need four of these shapes.  I found it was easier to do all four at once for each step, because it meant less resetting the compass.  Your results may vary...

Next, I measured down 1 3/4” from the center point and made a second mark.  Off this, I used the compass to make a  4 1/2” circle inside the first one.  Note that they don’t quite touch.  I also marked the center point.  The compass leaves a mark, but I wanted it to be clear because I’m going to be using it as a reference point. It may seem obvious, but this is the empty space “inside” the Scythe or between its wings, depending on how you view it. 

Right at the front, I went out 1 1/4” from the centerline on either side.  I made a few measurements and then made two short front-to-back lines parallel to the center line.  These are marking off the end of the wings and the gap that stretches across the front of the scythe.

Now, going off the center point of the smaller circle, I drew lines extending out over the hull and wings at 45 degree angles.   These are going to help me place the sloped armor on the Scythe.  I just want to do all the marks while this is big, flat, and solid.  Cutting’s the last thing I’ll do.

I also did a pair of lines that were 30 degrees off the center line.  These are for the cockpit section and the smaller armor sections at the front. 

This Is Important – Remember, none of these angled/ radiating lines are cut lines.  They’re just a reference for later

Once I had all this, it was time to cut.  Also, I was careful to save the center sections—they might be useful for the cockpit.  You’ll notice the Necron Warrior gives us a good sense of scale, and you can compare him to the codex art-image of the pilot up above.

Helpful Hint – These circles are big enough that you can cut the whole thing out with a good pair of scissors.  I just took my time and went slow.  It took about three minutes for each one.

Once I had all four sections cut out, I checked which pairs lined up best and glued them together.  I double-checked that they were lined up right, wrapped them in wax paper, and set them under a hardcover copy of Under The Dome and a few other Stephen King epics to make sure they stayed flat.  I let them dry overnight.

And for now, that’ll be it. 

No post next week because of Thanksgiving, but I’ll probably do two the week after just to get this done.

3 comments:

  1. Very cool idea! I think I'm going to do this too. I'll probably use a sander on the edges to make it look more sleek.

    ReplyDelete
  2. Well, wait until you see how I'm going to do the edges. I have a plan... ;)

    ReplyDelete
  3. Apologises for the spam comment *shameface* but we are after people to join our forum / blogging network. Interested? head on over to here; http://theshellcase.proboards.com/index.cgi?board=theblogcatalogue&action=display&thread=12

    Oh excellent idea with the scythe.

    ReplyDelete