The Defiler, Pt III

It look like the hit counter passed 10,000 over the weekend. Wow.

Okay, continuing on...

Cut out the leg sockets. They’re the vaguely star-shaped pieces on page four of the template. Glue four of these in place on the back section of the chassis, a little bit in from either end. They should be tall, not wide. The extra two are for the front arms, which we’ll get to in a while.

Start with the front legs. Put white glue on the inside of the socket, then pinch the four “arms” of the socket closed around the wooden bead. You’re probably going to have to hold them for a minute or three, and there will be some readjustment needed as you go. I held them for about five just to be safe. If you plan carefully, you can get both front legs in place and hold them both at the same time.

This Is Important -- Make sure the legs will sit flat once the model is in its standing pose. The more of an angle they’re at, the harder it will be to get the feet/ talons to line up when we get to them.

I did two legs on one Defiler, then moved to the other one and did two on that model. If you’re only working on one, you should probably give it about ten minutes for the glue to firm up before moving on. Once I had all four legs on and they were relatively solid, I flipped it over and put a few drops of glue in key points to make it even stronger. I gave this whole assembly about an hour to dry and it ended up good and rigid. Strong enough that I knew a leg wasn’t going to randomly drop off during a game.

While that lower section was drying, I went to work on the torso.

Actually, before I do that, I want to point out something that may please some of you. The majority of this template focuses on the bottom half of the Defiler and lustandtorment did a fantastic job with that. Something occurred to me the other day, though. What else can you do with the bottom half of a Defiler? To be more specific, what else could you do with the bottom half of a Defiler and the spare torso, head, and arms that come with the new Daemon Prince model?

Food for thought, eh?

So, for the battle cannons, I decided to use the same simple design I used to make an engine for the Hellblade a few weeks back. Cut a piece of card 2 1/4” wide by 3/4” long. You want to do a series of scores on it 1/4” apart, parallel to the short side, so when it’s done your piece of card has nine sections measuring 1/4” wide by 3/4” long. That last section’s going to be a tab, so it’s probably better if you cut the corners down. Roll this piece, glue it on the tab, and clamp it so you’ve got an octagonal cylinder 3/4”long. With me so far?

Next, cut three 1/4” strips that are three or four inches long. Wrap them tight around your hobby knife, a round pencil, or something like that so they get a good curve to them. Now wrap them around your cylinder and cut where appropriate. Glue one strip around the base of each cannon. For reference, the seam should be on the underside of your barrel, if your cannon looks better from one angle than another.

If you feel really daring, cut one strip to fit just inside the muzzle, too. That’ll give the sense of a thick, heavy barrel and help add to the illusion that it’s rounded, not octagonal. If you decide to do this, make sure the seam where the strip comes together is towards the top of the barrel. No one’s going to get a good look at the inside-top of a Defiler cannon.

From here on, I’m going to something slightly different with the cannon for each model. You can pretend these are optional bitz. Feel free to do whichever appeals to you on your own Defiler.

On the Nurgle model I glued the last strip around the barrel’s muzzle. Again try to make these outside-the-barrel seams on these strips line up, because you can hide them all on the underside of the cannon. This should give you a squat, very basic barrel, and it’ll look great once you add a few rivets with the 1/16” hole punch.

For the Khorne Defiler, I cut out eight triangles as shown. Score them down the middle and fold. Glue each of these little “spikes” on the business end of the cannon (creased edge up), butted up against the strip at the base. Make sure you set them on the octagonal edges, not on the flat surface. This will help hide the angular nature of the barrel. The triangle-spikes should end up with just a little bit hanging out over the muzzle, and result in a much more spiky-looking cannon.

Helpful Hint-- If you need to cut out a bunch of triangles for spikes (for Chaos or Orks or whatever) try this. For the ones above, mark out a strip 1/2” wide, then break it down into 1/2” x 1/4” rectangles. Sketch alternate diagonals into the rectangles (left-to-right, right-to-left, left-to-right, and so on). Now you’ve got a row of triangles going both ways, top and bottom. Nothing gets wasted and each cut is effectively cutting a side on two different triangles. Make sense?

There’s your battle cannon. Two versions of it, in fact.

As a final touch, cut a strip of card about 1” long by 1/8” wide. Score it to fit so it folds nicely into a “bracket” for the butt-end of the battle cannon. Now there’s something more substantial for the glue to grab when I attach the cannon to the gun shield.

Speaking of which... when you glue these two pieces together, make sure the cannon is lined up with the bottom edge of the gun shield. It will leave a bit hanging out over the top that you’ll need to fill in later on. I played with placement on this for a while and finally decided the easiest way to mount the cannon was just to make it flush with the front face of the shield. Putting it on top, on the angled section, just mkes it look too high up. If you’re more daring than me (and I’m sure some of you must be) you can try to notch the butt-end of the cannon so it can sit right on the angle of the torso.

That’s all for this time.

Oh, new anthology of the month is Robots Beyond, also from Permuted Press. Check it out.

The Defiler, Pt II

I’m getting buried in work stuff which is delaying the far-more-important work on this project. I’ve decided to break up building the Defilers into a few smaller, somewhat more frequent posts rather than wait until I’ve got the material for a full-sized one... which could take weeks.

Before I did anything else, I sat down and divvied up the components. As I mentioned before, I’m building two Defilers at a time here. The cleanest parts went to the Khorne one. Anything with rough edges or “shaggy” surfaces where the template came off went into the pile for the Death Guard model. If it ends up looking rusty or tweaked... all the better.

Back to building.

The waist piece is a bit thin and flimsy, so I decided to do two things to it. First was a bit of detail. Cut a long strip about 1/8” wide. Now cut that up into 3/8” lengths and glue them around the waist at regular intervals. This gave the visible part a bit of heft, too. Second thing was to build a small box. It’s 3/8” tall by 1/2” square, so it should fit completely inside the ring of the waist.

This is Important -- This little box needs to be flush with the top of the ring. If it’s a bit low, cut out another 1/2” square of card and see if that raises it up enough. Check first, then glue it on top of the box. There’s enough variation in card models that some people may not need it. Don’t worry about looks--this is all going to be hidden inside the waist-- but this needs to be flush to give you solid contact with the torso.

So you should have the waist on the chassis at this point, with the box inside the waist. I’d hold off attaching the torso yet. It’ll be a lot easier to work with if it stays separate for now.

Before you start to assemble the legs, it’ll help to figure out what kind of pose you want your Defiler to end up in. I’ve got two, but they’re going to be a bit different. The Khorne one will be a super-dreadnaught geared up to charge into close combat and lay waste to everything it can. The Death Guard one is essentially going to be a firebase, something that just hunkers down and starts shooting big guns. As such, I want to pose their legs to reflect these roles on the battlefield. The two front legs of the Khorne Defiler (or middle legs, depending on your point of view) are going to be higher so it ends up in a more aggressive, rearing-up pose. The Death Guard one will be squatting, all equal, all low.

So, as you begin to assemble these legs, remember those all-important tabs from the A section? This is where they pay off. Slide the D section into A. If you’ve done this right, the curved end of D should butt up against that tab. This means you can glue the legs in two different directions (along the plane of the joint and the plane of the tab) so this piece will be rock solid once it dries.

I assembled four legs for each Defiler. Once they were glued I covered them with wax paper, and set a mid-sized book on them to hold the joints flat. I left these to dry for about half an hour and went on to other things.

A bit of honesty as we move on to the next step. Remember before when I said all the time-intensive stuff was done? I lied.

The Defiler’s front claws are tough. I tried cutting them out with tabs on them and it just became a mess of 1/16” cuts in thirty different directions. I’m actually tempted to say don’t do them the way I did, even though they did turn out very nice and solid in the end. You could possibly save a lot of time and headaches just cutting the claws out of the template as-is and adding scraps of card as tabs where you need them. It might be a bit less structural, but I’m not even sure of that. I tried it on the “thumb” claws and it seemed to work, but they are a much simpler shape. I may experiment with this and get back to you.

While the claws dried I went back to work on the legs. As it says on the template, you’ll need to buy some wooden beads for the ball-and-socket joint on the legs. I went to my local craft/ hobby store and picked up two bags of 5/8” (15.9mm) wooden beads for $1.19 each (that’s $1.19 per bag, not per bead). The suggestion is for 1/2” beads, but in my opinion that makes the joint harder to assemble because of how deep into the leg the beads sink. Go a tiny bit bigger and make life easier on yourself.

Put a few drops of glue in the end of each leg and then push the bead into place. You’ll need to hold it for a few minutes, and it’s best to turn it around a few times so the glue hits as many points as possible. Watch out for leaks around the corners.

That’s all for now. I’ll try to get another quick update posted this weekend.

The Defiler

The Defiler is such a cool model. The first 100% Chaos-only tank. As such, it struck me as odd that there were so few templates floating around for it. I dug around and finally found a nice one at the BWC Archive 2, and the same one has since shown up at Paperhammer 40K, too. It was created by someone using the title lustandtorment (hey, I didn’t pick the name), and if any of you know who that is, please drop a note in the comments section so I can give credit where credit is due.

I was a bit torn about which army to make a Defiler for, though. I’d toyed with the idea of doing an all-paper Iron Warriors army, but that’s still a ways in the future. The Worldeaters could be good. I already made them that nice Mk. I Land Raider after all. But I also thought paperhammer could loan itself well to Nurgle, as it did with the Plague Tower.

In the end, because I’m a glutton for punishment, I decided to build two. One for Khorne, one for Nurgle. That’d let me show off weapons options here on the blog, too.

Helpful Hint -- If you decide to download this one over at Paperhammer 40K, you may have a moment of panic. The PDF opens with some very scrawled assembly instructions at the start that made me groan, too. Don’t worry. Skim past them, the template itself is fine.

One thing to note is that there aren’t any tabs on this one, and there will be a lot of overlapping if you’re not careful. However lustandtorment has made a pretty solid template without overcomplicating it, so it won’t take much work to place a few good gluing points here and there.

The first thing I cut out and assembled was the chassis. It looks a bit complex but fits together very nice. I glued it front to back first, let that dry, and then slid in one side. While that was drying, I cut a long strip of card about 1/4” wide and made some of those consummate V’s I’ve mentioned before. This made the chassis very solid and weight-supporting. Then the other side got glued and pushed into place. The chassis is a bit odd-shaped, so you’ll want to hold it until it dries, just so nothing slides out of position. That left the two flaps at the front, but they closed up with no problem.

So, with the chassis done for each Defiler, I decided to move on to the legs. They’re labeled (by letter) on the template, but I’d suggest actually marking the letter right on each individual piece. There’s a lot of sections here (more so since I’m building two of them), and there’s a few tricks and tweaks I’ve found for each one. I’ll go through them one at a time and explain. I’d label each of these a Helpful Hint but that would just get annoying fast, so hopefully it caught your attention just then.

First up is A. This is going to be the shoulder/ hip piece on all six limbs. Now, there’s debatable flaw in this part of the template. You’ll notice at the top of the A pieces there’s a square panel to fold over and give you a solid end. Thing is... you don’t want a solid end here. This hip/shoulder piece is eventually going to get attached to a wooden ball, so you want a space for the ball to fit into. When you assemble this section, fold the square panel down flat inside the arm. When you clamp your tab, you’ll end up holding it flat as a side-effect. Make sure you don’t confuse this square panel with the small flap on the other end--that one’s important

The B section is the middle of the front arms. It’s very important that you put tabs on the two long ends. These are going to bend around the curve and they’re going to need a tab so they’ve got something to grab with. Bend those end sections gently around your hobby knife before you start scoring and folding. Again, be gentle--you want the card to bend, not fold. Don’t worry if it’s not 100 flush with the curves once it's assembled. When the model’s done, these ends are going to be hidden inside the other sections.

Section C has a problem, but it’s an easy one to fix. This is the last section of the forward arms, where the big front claws attach. Problem is, unlike B or D, it doesn’t have an end piece to attach those claws to. It’s easy to make one, though. Just cut a strip of card 2 1/2” long and a hair under 1/2” wide (go for something like 7/16” if you need an exact measurement). Bend it gently around your hobby knife at the center. Once it’s got a curve to it, glue the sides and slide it into the end of C that does not have a little flap on it (like with A, the little flap is important). Try to make it line up with the curves on either side. If you have to, you can use a pencil to push it out slightly from the other end. Like on B, don’t worry if it’s not 100 flush with the curves--the claws will hide most of it once they’re attached.

Last but not least is D. These are going to be the Defiler’s four back legs. They go together almost exactly like the B sections.

Helpful Hint -- If you’re having a lot of trouble with getting the pieces to curve on B and D, you could just cut that whole section off and use the method I did to create the curve for section C.

Next is the torso, which is a bit trickier, but not much. On the template, you’ll see two large circles on either side of the torso. These are the “shoulders” that the weapons and close combat arms mount on. For now, ignore those circles and just cut along the straight lines (straight through the circles). Just like the chassis, I glued this section front-to-back first. In a rare move, I also decided to glue this tab on the outside of the body. It made things line up better, and it also gave a tiny bit of texture to this pretty blank section.

This is Important - When you add tabs to this piece, make sure that you score the front-to-back tab so it bends the other way. The Defiler’s back dips in right at the join. You don’t want to have to wrestle with this or re-cut it.

Once the front-to-back join was dry, I folded in the side tabs and slid each side into place. Because of all the angles, you may need to hold this for a few beats to make sure everything stays tight. If you end up with faint gaps or something that went in too far, don’t worry. The shoulders will help hide a lot of that.

Using one of new dollar coins (which I think are the same size as a Euro, but I’m not 100% on that...), trace and cut out three card circles for each shoulder. They should be just over an inch (about 1 1/16” if you want specifics again). You can glue these together so each shoulders is three circles thick, but do not attach them yet.

At this point the only thing left is the waist. It’s just a simple rectangle of cardboard on the templates. Put a tab at one end, then gently wrap the whole thing around your hobby knife to give it a good curve from end to end. Once you’ve got that, glue it and clamp it. I’ll be doing a lot more with the waist joint next time around.

At this point, believe it or not, all of the time-intensive stuff is done except for the claws. Next time I’ll build those, make some weapons, and start assembling.